Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System

(No reviews yet) Write a Review
SKU:
5175296
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
  • Bendpak PCL-18B-4 High Voltage 72,000 Lb. Mobile Lift System
$23,205.00
 
Full Description 

See the source imageThis PCL-18B mobile column lift system comes in a set of 4. When combined, the system lifts up to 72,000 lbs. Ideal for two-axle vehicles. Sets of 2, 6 and 8 are also available.

Set of 4 Mobile Column Lifts

With a full set of mobile column lifts, you'll lift vehicles up to 72,000 lbs. This weight class encompasses most heavy-duty and commercial semi-trucks. If you need more lifting power, upgrade to a set of 6 or double your capability with a set of 8. For a frame-engaging adapter, check out the PCL-18B cross beam. This handy tool allows you to safely remove tires and perform full wheel service on your vehicle.

 

Features

  • 18,000-lb. individual column capacity / 108,000-lb. maximum system capacity
  • Meets or exceeds the standards prescribed by ANSI/ALI ALCTV-2011
  • Two, four, or six column configurations can accommodate heavy duty trucks and light duty passenger vehicles
  • 208-240V, 3-phase main power system - optional voltages available upon request
  • SINGLE, PAIR or TEAM operation
  • For a standard four-column set, just three 30' cables are used leaving the front or back of the lift clear of cable obstructions
  • Simple operation, long service life and minimum maintenance
  • Intuitive controls allow the lift to be fully programmed and controlled from any column
  • Control systems feature 24-volt safety circuitry
  • The PLC and main system components are standard off-the-shelf brands rather than proprietary printed circuit boards or controls, which can be very expensive to service or replace
  • Smart electronics feature self-diagnostics and self-calibration functions
  • Sealed and enclosed linear potentiometers feature precision potentiometric output and high-frequency response for precise synchronization and communication of all columns throughout all operation cycles for precise, level lifting
  • Variable height limit settings can be programmed for shops with low ceilings or when specific vehicle service requirements necessitate specific rise heights
  • Two-speed lowering option – turtle or rabbit speed settings
  • Each column is equipped with a warning light and audible alarm for critical warning alerts
  • Emergency shut-off switches on each column quickly shut off power to the lift in the event an unsafe condition is detected by the operator
  • Separate key lock enclosure on each column
  • Electronics are multi-fuse protected
  • An enclosed electric-hydraulic power system that ensures quieter operation is better suited for sound-sensitive areas
  • Pallet-jack style steering wheels enable the columns to be lowered firmly on the floor vs. constantly loaded spring-type steering wheels that can cause columns to roll when unladen by the weight of a vehicle
  • Low-mounted power units and cylinders means a lower center of gravity, making the columns easier to move and less likely to topple vs. screw-drive systems with heavy overhead motors and drive systems
  • Extended forks accommodate wide tires and deep wheel configurations
  • Multi-width wheel forks with locking pins accommodate the widest range of wheels, eliminating the need for specialty wheel adapters
  • Tandem 8” diameter polyurethane covered steel wheels with sealed roller bearings easily roll over dirt and debris
  • Heavy-duty steel carriage rollers feature turned, ground and polished axle pins
  • Manual safety override valves on each column permit the lift to be lowered in the event of a power outage without the need for manual hand cranks
  • Durable forklift pockets provide simplistic handling when moving the lift columns from one facility to another
  • Inverted hydraulic cylinders feature an integrated safety valve to prevent accidental uncontrolled lowering in the event of oil pressure loss
  • Multiple, automatic, independent safety locks spaced every four inches ensure safe operation
  • Space-saving design, reduced column weight and a tight turning radius provides improved mobility
  • Use the lift to place vehicles on tall jack stands then use the columns to raise another vehicle in an adjoining bay
  • Durable powder-coat finish

 

Specs
  • Max column capacity: 18,000 lbs. / 8,165 kg
  • Configuration: Sold in sets of 2, 4, or 6 columns
  • Min column height: 97-1/2" / 2,572 mm
  • Max column height: 140-1/2" / 3,708 mm
  • Max lifting height: 71-1/2" / 1,889 mm
  • Length lifting fork: 13.6" / 360 mm
  • Overall length: 47-1/2" / 1,206mm
  • Min width inside lifting fork: 9-1/2" / 241 mm
  • Max width inside lifting fork: 22.7" / 576 mm
  • Overall width: 44" / 1,160mm
  • Turning circle: 40" / 1,016 mm
  • Column weight: 578 lbs. / 262 kg
  • Lifting speed: 85 sec
  • Motor: 208 V – 240 V / 50 Hz – 60 Hz / 3 Ph
  • Shipping weight: 1,394 lbs. / 634 kg (Ea. post) 

 **Shipping is FREE to direct points within the 48-contiguous states. A 5% RATZ Surcharge may apply if shipping to a rural shipping point. It is the buyer's responsibility to unload the freight at their location.

 

View AllClose
-->